Restore T-Mobile Galaxy S6 Edge Back To Stock with G925TUVU2COF8 firmware and recovery

Here, we have back to stock guide for T-Mobile Galaxy S6 Edge for all those people who want their device to be on original Samsung firmware, build G925TUVU2COF8, completely untouched. If you are unable to take OTA updates, then this would help you fix that as it will install the stock recovery back — a must for OTA update’s installation — and will also unrooted your device.

Moreover, if you had installed a custom ROM, that will be removed too. Thus, you will be back to what Samsung pre-installed for you, along with all the updates till and including OF8 build. The procedure is very easy, and you don’t need special preparation for this either. Just download the firmware from below, and you shall be good to go.

How to restore T-Mobile Galaxy S6 Edge back to stock on OF8 firmware

Downloads

  • OF8 firmware — Direct Link | File: G925TUVU2COF8_G925TTMB2COF8_TMB.zip (1.5 GB)
  • Odin PC software | File: Odin3_v3.10.6.zip (1.6 MB)

Supported devices

  • T-Mobile GALAXY S6 Edge, model no. SM-G925T
  • Don’t try this on any other Galaxy S6 Edge device than the model no. SM-G925T
  • Don’t try on any other device whatsoever!

Instructions

Disclamer: Installing an official firmware through Odin doesn’t void your device’s warranty, but it remains an unofficial process and thus you need to be cautious of it. In any case, you only are responsible for your device. We won’t be liable if any damage occurs to your device and/or its components.

Backup important files stored on your device before proceeding with the steps below, so that in case something goes wrong you’ll have backup of all your important files. Sometimes, Odin installation may delete everything on your device!

Step 1. Download the Odin software and firmware file from above.

Step 2. Install Galaxy S6 Edge driver (method 1 there!) first of all. Double click the .exe file of drivers to begin installation. (Not required if you have already done this.)

Step 3. Extract the firmware file (G925TUVU2COF8_G925TTMB2COF8_TMB.zip) now. You can use a free software like 7-zip for this. Install 7-zip, then right click on firmware file and under 7-zip, select ‘Extract here’. You should get the a file in .tar.md5 format now. We will be loading this file into Odin, to be installed on your Galaxy S6 (in step 10 below).

Step 4. Extract the Odin file. You should get this file, Odin3 v3.10.6.exe (other files could be hidden, hence not visible).

Step 5. Disconnect your Galaxy S6 Edge from PC if it is connected.

Step 6. Boot Galaxy S6 Edge into download mode:

  1. Power off your S6 Edge. Wait 6-7 seconds after screen goes off.
  2. Press and hold the three buttons Volume Down + Power + Home together until you see warning screen.
  3. Press Volume Up to continue to download mode.

Step 7. Double click on extracted file of Odin, Odin3 v3.10.6.exe, to open the Odin window as shown below. Be careful with Odin, and do just as said to prevent problems.
Odin 3.10.6

Step 8. Connect your Galaxy S6 Edge to PC now using USB cable. Odin should recognize your device. It’s a must. When it recognizes, you will see Added!! message appearing in the Log box in bottom left, and the first box under ID:COM will also show a no. and turn its background blue. Look at the pic below.

  • You cannot proceed until you get the Added!! message, which confirms that Odin has recognized your device.
  • If you don’t get Added!! message, you need to install/re-install drivers again, and use the original cable that came with device. Mostly, drivers are the problem (look at step 2 above).
  • You can try different USB ports on your PC too, btw.
    Odin 3.10.6 Added message

Step 9. Load the firmware file into Odin. Click the AP button on Odin and the select the .tar.md5 file from Step 3 above.

  • Info: When you load files, Odin checks the md5 of firmware file, which takes time. So, simply wait until that’s done and the firmware file is loaded. Don’t worry if Odin gets unresponsive for a while, it’s normal. Binary size will also show up in Odin.
    Odin 3.10.6 Firmware loaded after md5 check

Step 10. Make sure Re-partition checkbox is NOT selected, under the Options tab. Don’t use PIT tab either. Go back to Log tab btw, it will show the progress when you hit start button in next step.
Re-partition Remains Off

Step 11. Click the Start button on Odin now to start flashing the firmware on your Galaxy S6 Edge. Wait till installation is finished, after which your S6 Edge will reboot automatically. You’ll get PASS message as shown below upon successful installation from Odin.

  • If Odin gets stuck at setup connection, then you need to do steps 6 to 11 again. For this, close Odin, disconnect your S6 Edge and then start from step 6 again.
  • Or, if you get FAIL in the top left box, you need to try flashing again, as stated just above.
    Odin 3.10.6 Pass Message Appears

Step 12. First start of the device may take time, so wait patiently again. Check the Settings > About phone to confirm new firmware.

That’s it. Enjoy your fully Back to Stock T-Mobile Galaxy S6 Edge on OF8 firmware!