Have you bought the Galaxy S3 I9300T and played around with custom ROMs and modifications but want to go back to a stock firmware that completely resets it? If yes, then you can flash the TDUALF2 firmware on your I9300T which will completely reset it to stock firmware, removing any changes you may have made to the system, while preserving your personal content on the SD cards.
Read on to find out how you can flash the TDUALF2 firmware on your Galaxy S3 I9300T to restore it to stock firmware.
This hack and the guide below are compatible only and only with Galaxy S3, model number i9300T. It’s not compatible with the I9300, US variants or other devices. Check your device’s model number in: Settings » About phone.
The methods and procedures discussed here are considered risky and you should not attempt anything if you don’t know completely what it is. If any damage occurs to your device, we won’t be held liable.
How to Restore Galaxy S3 I9300T with TDUALF2 Firmware
- This procedure will wipe all your apps, data and settings (but it will NOT touch your SD cards, so don’t worry about those). Backup your Apps and important data — bookmarks, contacts, SMS, APNs (internet settings), etc. This Android backup guide would help you.
Important! Don’t forget to at least make a backup of your APN settings, which you can restore later if your data connection does not work after installing the ROM. Use the backup guide to find out how.
- Download and install the software Kies on your computer, which will install the necessary drivers for the phone.
You can also download the drivers directly — download from here: 32 bit (x86) Windows | 64-bit (x64) Windows
- Download the firmware.
Download Link | Alternate Link | Filename: I9300TDUALF2_I9300TTHLALE3_THL.zip
- Extract the I9300TDUALF2_I9300TTHLALE3_THL.zip file on the computer to obtain a file named I9300TDUALF2_I9300TTHLALE3_I9300TDULF2_HOME.tar.md5.
- Download the Odin PC software. If you are new to this, Odin is what is used to flash stuff – firmwares, kernels, etc. – on Samsung phones. We’ll use Odin to flash the firmware file obtained in step 4.
Download Odin3 v3.04 | Filename: Odin3_v3.04.zip
- Extract the contents of the Odin3_v3.04.zip file to a folder on your computer.
- Now, turn off your Galaxy S3 and wait for it to shut down completely.
- Then, put the phone into download mode. To do so, press and hold these keys together: Volume Down + Home + Power till the screen turns on. Then press Volume Up to enter download mode.
- Open Odin by double-clicking on the Odin3 v3.04.exe file obtained in step 6 after extracting Odin3_v3.04.zip.
- Important! Connect your phone to PC now. You should get the message “Added !!” under Odin’s message box in the bottom left.
If you don’t get this message, make sure you installed drivers correctly (using Kies or directly) as given in step 1. If it still doesn’t work, try changing to another USB port on the computer and also use the USB ports on the back if you have a desktop PC.
- Click on the PDA button in Odin, then browse to and select the I9300TDUALF2_I9300TTHLALE3_I9300TDULF2_HOME.tar.md5 file obtained in step 4 above.
- Important! Do not make any other changes in Odin except selecting the required files as given in step 11. Leave all other options as they are. And make sure Re-Partition check box is not selected.
Your Odin screen should look like this after the above steps (the COM# in the ID:COM box may be different, which is normal):
- Now, click the Start button to start flashing the firmware on your phone. When the flashing is complete and is successful, you’ll get a PASS message (with green background) in the left-most box at the very top of the Odin, and the phone will automatically reboot. When you see the Samsung logo, you can safely unplug the cable. What do if Odin gets stuck or doesn’t do anything: If ODIN gets stuck on setup connection or at any stage of this process after you’ve hit the Start button, and doesn’t seem to be doing anything, or if upon completion of the process you get a FAIL message (with red background) in ODIN, do this: disconnect the phone from the PC, close ODIN, remove battery for 4-5 seconds, re-insert it, turn phone on in Download mode again, and do the procedure again from Step 9.
- After you’ve got the PASS message, it’s possible — and okay — that phone might get stuck at the Samsung logo, and not boot up completely. It’s okay, just follow the steps 14.1 to 14.4, and you will be fine. And, if it boots up fine, without getting stuck, you’re fine. The Android 4.0 installation has been done successfully. So, do the following if your i9300 doesn’t move beyond the Samsung logo when booting up after getting PASS in Odin (make sure you wait some good 10-15 mins to confirm that it’s stuck):
- Boot to recovery mode — for which, first power off phone (by removing battery and reinserting it), wait for 5-6 seconds, and then press and hold Home + Volume Up + Power keys together till the screen turns on, then let them go to boot into recovery. Once you are in recovery mode, use volume keys to move the selection up and down and power or home key to select the option.
- Go to Wipe data/Factory Reset and select it. Select Yes on next screen.
- Now, go to Wipe Cache and select it. Confirm Yes on next screen.
- Then, select reboot system now to reboot the phone, which will now boot properly.
- If you run into any roadblocks while flashing the firmware, let us know and we’ll help you out.
That’s it, the TDUALF2 firmware has been flashed on your Galaxy S3 I9300T, restoring it to a new and refreshed state. Do let us know how it works for you, in the comments.
If you have the I9300 and not the I9300T, you can follow this guide to restore it to stock.