Official Android 4.1.2 Jelly Bean Update for AT&T Samsung Skyrocket SGH-I727 [Guide]

Samsung, or rather the US carriers, are on a roll – official Android 4.1 Jelly Bean updates have been coming in for various variants of the Galaxy S2 over the past few weeks, and now the update for the AT&T Skyrocket has begun rolling out as well.

The Jelly Bean update brings many new features and improvements – smoother interface framerate thanks to Project Butter and improved responsiveness, actionable and expandable notifications, Google Now, offline voice typing, better browser performance, improved search, and lots more under the hood enhancements.

But perhaps the most important change is that Samsung’s new Nature UX found on devices like the Galaxy S3 replaces the default TouchWiz interface, along with other new features such as new widgets, two homescreen modes, Direct Call, Smart Stay, improved camera features, Samsung’s S Cloud service and more, meaning you’ll find a totally revamped interface and experience after the update.

The update’s full firmware is now available for download for those that want to manually install the update, especially if they were on a custom ROM but now want to taste the official Jelly Bean. If you’re new to this or aren’t too familiar with manual firmware flashing, the guide below has step-by-step instructions to help you out.

So, let’s take a look at the manual update procedure. If you are only looking for the download link and not the whole guide, you can get that in step 3 below.

Compatibility

The guide below is compatible only and only with AT&T Samsung Skyrocket, model number SGH-I727. It will not work with other carrier variants. Check your device’s model number in: Settings » About phone.

Warning

The methods and procedures discussed here are considered risky and you should not attempt anything if you don’t know completely what it is. If any damage occurs to your device, we won’t be held liable.

How to Update AT&T Samsung Skyrocket to Android 4.1.2

  1. [Important] You might need to wipe the data on the phone to make the firmware boot up properly, especially if you flash it over a custom ROM. To be sure you do not lose any data, backup your Apps and important data — bookmarks, contacts, SMS, APNs (internet settings), etc. This Android backup guide would help you. The SD card contents are always safe, so there is no need to back up those. Only backup apps and personal data.
  2. Download and install the software Kies on your computer, which will install the necessary drivers for the phone.
    Download Kies
    You can also download the drivers directly — download from here: 32 bit (x86) Windows |   64-bit (x64) Windows
  3. Download the firmware.
    Download Link
  4. Extract the file downloaded in step 3 on the computer to obtain a file named KIES_HOME_I727UCMC1_I727ATTMC1_844945_REV02_user_low_ship.tar.md5 (the file name may end at .tar, which is normal). This is the actual firmware file that we need to flash on the phone.
  5. Download Odin. If you are new to this, Odin is what is used to flash stuff – firmware, kernels, etc. – on Samsung phones. We’ll use Odin to flash the firmware file obtained in step 4.
    Download Odin3 v3.04  |  Filename: Odin3_v3.04.zip
  6. Extract the contents of the Odin3_v3.04.zip file to a folder on your computer. You should obtain a total of 4 files after extracting it.
  7. Turn off your phone and wait for it to shut down completely.
  8. Now, plug in your USB cable to the computer but not to the phone. Then, press and hold the Volume Down + Volume Up keys together, and while holding both keys pressed, connect the USB cable to the phone, then let go of the volume buttons. At the “Warning!” screen, press the Volume Up key to make the phone boot into download (Odin) mode.
  9. Open Odin by double-clicking on the Odin3 v3.04.exe file obtained in step 6 after extracting Odin3_v3.04.zip.
  10. Important! Connect your phone to PC now. You should get the message “Added !!” under Odin’s message box in the bottom left.
    • If you don’t get this message, make sure you installed drivers correctly (using Kies or directly) as given in step 1. If it still doesn’t work, try changing to another USB port on the computer and also use the USB ports on the back if you have a desktop PC.
  11. Click on the PDA button in Odin, then browse to and select the KIES_HOME_I727UCMC1_I727ATTMC1_844945_REV02_user_low_ship.tar.md5 file obtained in step 4 above.
  12. Do not make any other changes in Odin except selecting the required files as given in step 11. Leave all other options as they are. Make sure Re-Partition check box is not selected.
  13. Now, hit the START button to start flashing the firmware on the phone. When the flashing is complete, your phone will automatically reboot — and when you see the Samsung logo, you can safely unplug the cable. Plus, you’ll get a PASS (with green background) message in the left-most box at the very top of Odin.
    • What to do if Odin gets stuck: If ODIN gets stuck and doesn’t seem to be doing anything, or you get a FAIL message (with red background) in ODIN, do the following – disconnect the phone from the PC, close ODIN, remove battery, re-insert it, and do the procedure again from Step 8.
  14. [Important] After you get the PASS message and the phone reboots, the phone might get stuck at the booting animation. If that happens, perform the following steps to make it boot. Remember that these steps will wipe your personal data like contacts, apps, messages, etc. If your phone has already booted, skip these steps, your phone has been restored/fixed successfully:
    1. Boot to recovery mode — for which, first power off phone (by removing battery and reinserting it), wait for 5-6 seconds, and then press and hold Volume Up + Volume Down + Power keys together till the phone vibrates, then let go of the power button (but not the volume buttons) till the phone boots in recovery. Once you are in recovery mode, use volume keys to move the selection up and down and power key to select the option.
    2. Go to Wipe data/Factory Reset and select it. Select Yes on next screen.
    3. Then, select reboot system now to reboot the phone, which will now boot properly.
  15. If you run into any roadblocks while flashing the firmware, let us know and we’ll help you out.

The Android 4.1.2 Jelly Bean update is now installed on your AT&T Skyrocket, and you can enjoy a faster and improved experience with lots of new features and enhancements. Do let us know how the update works for you, in the comments below.

Via: Sammobile

27 Comments

  1. Thank you for providing these instructions – they worked like a charm, first time. I tried for almost two hours to get Kies to work for the upgrade and never could (Kies is such a flaming piece of cr*p).

  2. Thank you for providing these instructions – they worked like a charm, first time. I tried for almost two hours to get Kies to work for the upgrade and never could (Kies is such a flaming piece of cr*p).

  3. Thank you for providing these instructions – they worked like a charm, first time. I tried for almost two hours to get Kies to work for the upgrade and never could (Kies is such a flaming piece of cr*p).

  4. THE ONLY SITE THAT WORKED FOR ME!!! THANKS A TON!!!

  5. THE ONLY SITE THAT WORKED FOR ME!!! THANKS A TON!!!

  6. THE ONLY SITE THAT WORKED FOR ME!!! THANKS A TON!!!

  7. thanks bro it worked!

  8. thanks bro it worked!

  9. thanks bro it worked!

  10. thanks men it’s works….

  11. thanks men it’s works….

  12. thanks men it’s works….

  13. it says cant open the serial(com) port

  14. it says cant open the serial(com) port

  15. it says cant open the serial(com) port

  16. Would this remove a phone’s unlock?

  17. Would this remove a phone’s unlock?

  18. Would this remove a phone’s unlock?

  19. This worked like a charm, however, I still see AT&T apps that I would like removed. Example YP, ATT Derive mode, att family map, att locker, etc
    Did I miss a step?

    Thank you in advance.

  20. This worked like a charm, however, I still see AT&T apps that I would like removed. Example YP, ATT Derive mode, att family map, att locker, etc
    Did I miss a step?

    Thank you in advance.

  21. This worked like a charm, however, I still see AT&T apps that I would like removed. Example YP, ATT Derive mode, att family map, att locker, etc
    Did I miss a step?

    Thank you in advance.

  22. i can’t complete step 11 because odin goes into my guestt user account instead of my main one and i can’t switch it

  23. i can’t complete step 11 because odin goes into my guestt user account instead of my main one and i can’t switch it

  24. i can’t complete step 11 because odin goes into my guestt user account instead of my main one and i can’t switch it

  25. I just installed the update for S2 Skyrocket and my phone is stuck on ATT logo screen and will not complete restart. Any suggestions? All was done automatically through Keis Air and did not ask/reguire for Odin download.

  26. I just installed the update for S2 Skyrocket and my phone is stuck on ATT logo screen and will not complete restart. Any suggestions? All was done automatically through Keis Air and did not ask/reguire for Odin download.

  27. I just installed the update for S2 Skyrocket and my phone is stuck on ATT logo screen and will not complete restart. Any suggestions? All was done automatically through Keis Air and did not ask/reguire for Odin download.

Comments are closed.