Easy Guide to Install ClockworkMod (CWM) Recovery on AT&T Galaxy S3

ClockworkMod recovery is quite an important tool in the Android world, letting you flash custom ROMs and modifications on devices. And it has always been easy to install CWM recovery on Samsung devices, and it isn’t any different for the AT&T Galaxy S3, which was just recently launched. The guide below will help you flash CWM recovery on your AT&T Galaxy S3, with step-by-step instructions.

Read on to find out how you can install ClockworkMod recovery on your AT&T Galaxy S3.

Compatibility

This guide below is compatible only and only with the AT&T Galaxy S3. It’s not compatible with any other Galaxy S3, it only works for AT&T variant. Check your device’s model in Settings» About phone.

Warning!

The methods and procedures discussed here are considered risky and you should not attempt anything if you don’t know completely what it is. If any damage occurs to your device, we won’t be held liable.

How to Install ClockworkMod Recovery on AT&T Galaxy S3

  1. [Optional] Just to be safe, backup all your apps, data and settings.  Backup your Apps and important data — bookmarks, contacts, SMS, APNs (internet settings), etc. This Android backup guide would help you.
  2. Download and install the drivers for the phone on the computer.
    Download Drivers
  3. Download Odin 3.04, the software that we will use to flash recovery.
    Download Odin  |  Filename: Odin3-v3.04.zip
  4. Extract the Odin3-v3.04.zip file to a convenient location on the computer.
  5. Download the ClockworkMod recovery file.
    Download CWM Recovery  |  Filename: clockworkmod.tar
  6. Turn off your phone. Then boot into download mode. To do so, hold down the Volume Down, Home and then the Power buttons together until a Warning!! message is displayed on the screen. Here, press Volume Up to enter download mode. A green Android and the text Downloading will be displayed on the screen.
  7. Now, open Odin by clicking on the Odin3 v3.04.exe file which you obtained after extracting Odin3-v3.04.zip in step 4.
  8. Then, connect the phone to the computer with the USB cable and wait for Windows to finish installing drivers. Odin will say Added!! in the message box on the bottom left if the phone is detected successfully. If not, make sure the drivers are installed and also try using a different USB port – preferably a USB port on the back if using a desktop computer.
  9. In Odin, click on the PDA button, then select the clockworkmod.tar file that you downloaded in step 5.
  10. Important! Do not touch any other button or make any other changes in Odin except selecting the required file as given in step 9.
  11. Now, hit the START button to start flashing ClockworkMod recovery on the phone. When the flashing is complete, your phone will automatically reboot — and when you see the Samsung logo, you can safely unplug the cable. Plus, you’ll get a PASS message (with green background) in the left-most box at the very top of Odin. What to do if Odin gets stuck: If ODIN gets stuck and doesn’t seem to be doing anything, or you get a FAIL message (with red background) in ODIN, disconnect the phone from the PC, close ODIN, remove battery, re-insert it, then repeat the procedure from step 7.
  12. Now, to test out ClockworkMod recovery, turn off the phone. Hold down Volume Up, Home and then the Power button together until the screen turns on, then let them go. The phone will boot into ClockworkMod recovery in a few seconds. Navigating ClockworkMod recovery can be done by using the volume buttons to scroll up/down and the Home button to select an option.

ClockworkMod recovery is now installed on your AT&T Galaxy S3. Let us know how it works!

10 Comments

  1. hi followed instructions to install cmw everthing went good oden said pass when testing to see if it worked boot into recovey it says android system recovery prety sure it didnt work isnt this stock one new to all this flashing and rooting can any one help i did this twice with same results thanks

  2. hi followed instructions to install cmw everthing went good oden said pass when testing to see if it worked boot into recovey it says android system recovery prety sure it didnt work isnt this stock one new to all this flashing and rooting can any one help i did this twice with same results thanks

  3. hi followed instructions to install cmw everthing went good oden said pass when testing to see if it worked boot into recovey it says android system recovery prety sure it didnt work isnt this stock one new to all this flashing and rooting can any one help i did this twice with same results thanks

  4. i followed instructions, and everything was working fine, but when i tried to boot into cwm recovery mode, nothing happened. Help?

  5. i followed instructions, and everything was working fine, but when i tried to boot into cwm recovery mode, nothing happened. Help?

  6. i followed instructions, and everything was working fine, but when i tried to boot into cwm recovery mode, nothing happened. Help?

  7. i followed instructions, and everything was working fine, but when i tried to boot into cwm recovery mode, nothing happened. Help?

  8. You have to un-check the auto reboot option. When you get the pass message you have to take your battery out and put it back in, then you can boot into recovery mode by holding the up volume home and power buttons.

  9. You have to un-check the auto reboot option. When you get the pass message you have to take your battery out and put it back in, then you can boot into recovery mode by holding the up volume home and power buttons.

  10. You have to un-check the auto reboot option. When you get the pass message you have to take your battery out and put it back in, then you can boot into recovery mode by holding the up volume home and power buttons.

Comments are closed.